- What should bearing seals be checked for?
- How do you start from an uphill parking space without rolling backwards?
- What is a wheel bearing seal?
- Why is it important to get car inspected?
- What is the minimum allowable tread depth for steer tires?
- What is the most important reason for doing a vehicle inspection CDL?
- What is the most important hand signal?
- How can you start moving without rolling backwards?
- Is the pre trip inspection test hard?
- How do you manually take off a hill?
- What are the 3 hand signals?
- Why put the starter key in your pocket during the pre trip inspection?
- When should I get post trip inspection?
- When you do a walk around inspection you should check?
- What 3 kinds of emergency equipment must you have?
- What hand signal means stop?
- When entering a freeway the best speed to be going is?
- What is the most important reason to inspect your truck or bus?
What should bearing seals be checked for?
What should wheel bearing seals be checked for.
Grass and dirt.
Color of paint used on cover..
How do you start from an uphill parking space without rolling backwards?
While holding the foot brake down, set the parking brake firmly.Move your foot to the accelera- tor, and accelerate until you feel the engine start to pull.Release the parking brake as you continue to accelerate.
What is a wheel bearing seal?
Wheel seals are designed to keep your wheel bearing lubricant within the wheel end, and keep all debris, dirt, and other contaminants out while on the road. They can be installed directly into the hub or onto the spindle with dedicated installation tools, dependent upon the seal.
Why is it important to get car inspected?
Why is a vehicle inspection important? A vehicle inspection or circle check is a physical and visual inspection of the vehicle before you use it. Making a report of issues helps to make sure the vehicle is safe to use. … Report all issues to your supervisor or to individuals responsible for vehicle maintenance.
What is the minimum allowable tread depth for steer tires?
4/32According to Federal Motor Carrier Safety Administration (FMCSA) regulations, the minimum tread depth for a steer tire is 4/32 of an inch on every major tread groove. If one spot on one groove is less than 4/32, then a driver will be issued a citation.
What is the most important reason for doing a vehicle inspection CDL?
What is the most important reason for doing a vehicle inspection? Safety is the most important reason you inspect your vehicle, safety for yourself and other road users.
What is the most important hand signal?
The most important hand signal to discuss and agree upon is the one used for “stop.” It is important that the helper stand at the back of the vehicle, in a spot where the driver can see them clearly. This will help collisions and aid the driver during “blind spots.”
How can you start moving without rolling backwards?
If stopped on a hill, how can you start moving without rolling back? partly engage the clutch before you take your right foot off the brake. Release the parking brake with enough engine power. the hand valve can be applied to keep from rolling back.
Is the pre trip inspection test hard?
Learning the vehicle inspection portion of the CDL test is difficult for many students. In most states, there are over 100 items to be checked on the tractor-trailer. Passing the test requires each student to study and memorize the items tested.
How do you manually take off a hill?
Method 1 of 3: Using the handbrakeStep 1: Apply the handbrake. … Step 2: Press the gas pedal. … Step 3: Release the clutch and handbrake. … Step 1: Apply pressure to the clutch and brake pedal. … Step 2: Press the gas pedal with your heel. … Step 3: Let off the clutch. … Step 4: Press the gas pedal.More items…•
What are the 3 hand signals?
Similar to automobile signaling, there are three primary signals: Left turn/overtaking, Right turn, and Stopping/braking.
Why put the starter key in your pocket during the pre trip inspection?
Question: For what reason do you keep the starter switch key in your pocket during the pre-trip inspection? Answer: So no one moves the vehicle while you are inspecting underneath it.
When should I get post trip inspection?
According to 49 CFR §396.11, if your vehicle carries passengers, you must provide a post-trip inspection at the end of each day’s work.
When you do a walk around inspection you should check?
Name some things you should check on the front of your vehicle during the walk-around inspection.Go to front of vehicle and check that low beams are on and both of the 4-way flashers are working.Push dimmer switch and check that high beams work.Turn off headlights and 4-way, hazard warning flashers.More items…•
What 3 kinds of emergency equipment must you have?
What three kinds of emergency equipment must you have? Spare electrical fuses, three red reflective triangles, properly charged and rated fire extinguisher.
What hand signal means stop?
I’m Stopping Extend your left arm out the driver’s window and point your arm down with your fingers extended and your palm facing rearward. This is the universally accepted sign that you’re decelerating, and other drivers understand it intuitively. Keep your arm in this position at least until you come to a full stop.
When entering a freeway the best speed to be going is?
Enter the freeway at approximately the same speed as traffic making sure you have enough room to merge safely (Remember the maximum speed allowed is 65 mph on most freeways). You must signal as you start to merge into traffic and should continue to signal until you are fully merged.
What is the most important reason to inspect your truck or bus?
Safety is the most important reason you inspect your vehicle, safety for yourself and for other road users.